Innokin iTaste MVP 20W

The new Innokin iTaste MVP 20W: 20 watts of intelligent vaping power in the legendary 100% stainless steel body of Innokin iTaste MVP. The MVP20W is now has been powered up to 20 watts and upgraded with a better chip and sleeker look. The iTaste MVP20W now has a high quality flush 510 spring loaded connection that is designed to connect perfectly with all standard 510 tanks. An EGO thread adapter is packaged with the MVP20W so you can also use eGo threaded tanks as well.

The MVP20W is a variable voltage with a range of 3.3v-7.5v adjustable in 0.1 volt increments and variabel attage from 6.0w - 20.0w adjustable in 0.5 increments.The easy to use integrated ohm meter will display the resistance of any attached tank and the handy puff counter helps you keep track of your daily vaping habits.

The iTaste MVP20W is smarter with a 32-bit ARM microprocessor which means far faster data processing power and superior vaping performance. The steady VDC power output with an output voltage accuracy of +-1% greatly reduces noise and increases battery life and reliability.

The large capacity of a internal 2600mah battery means you can depend on the long lasting power of the MVP20W and it's also a backup portable charger that can power your mobile phone and other electronic devices.



Features and Specs:

Dimensions: 4.21"L x 1.61"W x 0.86"D

Variable Voltage:
Voltage can be adjusted from 3.3 � 7.5 volts in .1 volt increments.

Variable Wattage:
Wattage can be adjusted from 6.0 � 20.0 Watts in .5 watts increments.

Battery Level Indicator:
The MVP20W battery capacity is displayed via green, yellow and red LED.
Green = Almost fully Charged. When the MVP20W fully recharged the LED light will power off.
Yellow = Half Power.
Red = Low Power. Charge the MVP20W.

Large battery capacity:
The MVP20W has a built-in 2600 mAh polymer Li-Ion rechargeable battery.

ON/OFF battery switch:
Press the power button three times in rapid succession to turn on the MVP20W. When the MVP20W is powered on hold down the button to activate the atomizer and vape. When the MVP20W is not in use, press the button three times in succession to power off the MVP20W. Always power off the MVP20W when it is not being used, or when it is going to be stored in a pocket, bag or purse.

Ohms meter:
Reads the resistance of your atomizer/cartomizer/clearomizer.

Puff Counter:
The integrated Puff counter will record the number of puffs you have taken. Either press �P �button or �U� button for 1 second to check the number of puffs. The Puff Counter will reset to 0 whenever the device is powered off.


SAFETY:

10 second Cutoff:
If the activation button is held for longer than 10 seconds the MVP20W will stop firing until the button is released and pressed again.

Low Voltage Warning:
The Red LED and Battery bar will continue blinking when the battery capacity is lower than 3.3V and the MVP20W will power off automatically.

Short Circuit/Atomizer Protection:
Short Circuit/Atomizer Protection protects the MVP20W against shorted atomizers and will stop the unit from functioning in unsafe conditions.

Over-Discharge Protection:
The MVP20W monitors the battery voltage and will automatically power off when the battery is discharged.

Pass-through Technology:
The MVP20W is recharged with a Micro USB cable. When plugged into a power source the MVP20W can also be vaped and charged at the same time with Innokin Technology�s �Vape while you charge� pass-through technology.

Remembers last Voltage or Wattage setting:
When the MVP20W is turned off it will store the current voltage or wattage setting and it will retain the setting when the MVP20W is powered on.

Built-in 3 digit display:
Digital display shows the Ohms meter, Voltage / Wattage setting and the number of Puffs taken since last time the battery was turned off.

Portable power source for electronic products
To charge your portable electronic device with the MVP20W - set the small pin switch on the bottom of the MVP20W to the ON position and connect a micro USB cable to the USB OUTPUT port (DC 5V, maximum output current 0.5A)To maximize the battery charge of your MVP20W please ensure that the bottom switch is set to the Off position when you are not using the portable charger function.


Technical Specifications:

• Operating Voltage: 3.3V-7.5 V
• Operating Wattage: 6.0W-.20W
• Standby current: 100uA max
• Maximum output Wattage: 20W
• Maximum output Current：6A
• Maximum output Voltage: 7.5V
• Clearomizer Resistance: 1.0 Ohm (minimum)
• Battery: Built-in 2600 mAh polymer Li-Ion rechargeable battery.
• Charging: Micro USB DC5V/1000mA
• OUTPUT port ：DC5V /1000mA

The Innokin iTaste MVP20W will include a 30 day Limited Warranty against any manufacturing defects from the date of delivery. Scratches and discoloration from regular use is considered normal wear and tear and is not covered by warranty.

NOTE: Use special caution when working with Li-ion cells, they are very sensitive to charging characteristics and may explode or burn if mishandled. Make sure the user has enough knowledge of Li-Ion rechargeable batteries in charging, discharging and assembly before use. Always charge in/on a fire-proof surface. Never leave charging batteries unattended. We are not responsible for damage if there is any modification of the batteries/chargers in any form or shape (including pack making). We are not responsible for any damage caused by misuse or mishandling of Li-Ion batteries and chargers. We only recommend using Lithium Ion rechargeable batteries with a control circuit (protection PCB) to assure safe charge, discharge, etc, use of lithium ion batteries without a protection circuit is potentially hazardous

myvaporstore.com will not be held responsible or liable for any injury, damage, or defect, permanent or temporary that may be caused by the improper use of a LI-ION battery. Please have a basic understanding of the batteries you are using and how to care for them properly.

MODS & PVs
MODS & PVs -> 3W - 20W Devices
MODS & PVs -> Box Mods
MODS & PVs -> Built-In Battery
New Arrivals